We build the hob into the worktop
When the built-in panel is installed in a new modern set, a table under the hob, and there is no special hole for mounting the case, you need to prepare a set of tools in advance. This will require a jigsaw and a drill.
To connect to the network, you need a screwdriver, pliers. It is worth taking care of the serviceability of the outlet, the hob will turn on in it. The choice of location is done in advance.
How to properly cut a place for the stove in the countertop
It is imperative to follow the exact parameters of the plate itself, for this you can use the template attached to the instructions. You need to take a large square to draw a rectangle on your desktop.
To get a hole, you need to find a saw with the appropriate blade. Using a hammer drill, you will first need to drill small holes along all corners of the rectangle.
The execution process will take approximately 10 minutes. How to properly cut the worktop under the hob.
Detailed Correct Work Flow:
- Determine the contour of the slab.
- Place the unit on a part of the table.
- Draw the middle on the prepared flat surface, mark the incision line.
- Place shims at the bottom for an accurate result.
- Leave 5 cm between the cabinet and the worktop.
- Create start holes.
- Make cuts along the lines (work with a jigsaw).
- Place the surface in the resulting hole.
- Fasten with self-tapping screws, connect.
- Check and evaluate the result obtained.
Thus, having studied the instructions and rules, everyone can cope with the task assigned to him.
Rules for installing the hob in the worktop
At the very beginning, even before the equipment is inserted, it is necessary to make sure that it is in good working order, there are no defects in devices and devices. After the holes are ready, you need to carefully, without pressing hard, insert the technique until it fits perfectly to the edges of the table.
You can pre-apply a small coat of sealant. Most importantly, the built-in appliances must lie perfectly on the surface. With the help of clamps that perform the function of fixing, the fixing process is carried out (installed from below).
Worktop markings
The layout on the table is carried out strictly taking into account the size of the built-in household appliances (spelled out in the passport). Transfer all panel dimensions to the table surface with a pencil.
Near each side, make one hole, the diameter of which will be no more than 10 mm, and only then carefully cut the niche itself with a jigsaw.
Connection
The procedure for connecting a selected flat cooking surface is the final step in setting it up.This process requires increased attention and a responsible approach.
Each type of equipment (electric or gas version) requires special conditions and connection rules. You need to familiarize yourself with them.
Gas
Connecting a gas-type stove will take a little time, and you can handle it yourself. Having installed and securely fastened the device, it remains only to connect it to the gas main. First, you need to make sure the integrity of the gas pipeline.
Flexible hoses (gas) are used for connection. There are threaded nuts at the end of the hose and gaskets inside for a secure connection. Do not tighten the nuts too much (this can be done with the special wrench included in the kit). If necessary, the work can be entrusted to professionals in this matter. After installation, the hose is connected to the gas pipe, then to the equipment.
Electric
First of all, when connecting the electrical option, you need to take care of the presence of a working outlet, check the voltage in the network. The cross-section of the wires must correspond to the optimum power.
The hob is connected to a separate electrical line.
Installation Precautions
Be sure to pay attention to some important rules for cutting the slab on the table. The thickness of the table surface on which the panel is to be embedded should not be more than three centimeters.
A fragile and weak structure will not be able to withstand a long load. In addition, it is worth monitoring the health of the sockets, electricity and the tightness of the gas pipeline to which the equipment is connected.
After making sure of the quality of all available devices, you can be sure of the safety of further use.
Video: how to properly embed the hob into the kitchen worktop
